GHALDA AULIA (2021) HYPOTHERMIA BLANKET BERBASIS ARDUINO. S1 thesis, Universitas Muhammadiyah Yogyakarta.

[thumbnail of Halaman Judul] Text (Halaman Judul)
Halaman Judul.pdf
Download (572kB)
[thumbnail of Lembar Pengesahan] Text (Lembar Pengesahan)
Lembar Pengesahan.pdf
Restricted to Registered users only
Download (534kB)
[thumbnail of Abstrak] Text (Abstrak)
Abstrak.pdf
Restricted to Registered users only
Download (123kB)
[thumbnail of Bab I] Text (Bab I)
Bab I.pdf
Download (296kB)
[thumbnail of Bab II] Text (Bab II)
Bab II.pdf
Restricted to Registered users only
Download (93kB)
[thumbnail of Bab III] Text (Bab III)
Bab III.pdf
Restricted to Registered users only
Download (838kB)
[thumbnail of Bab IV] Text (Bab IV)
Bab IV.pdf
Restricted to Registered users only
Download (523kB)
[thumbnail of Bab V] Text (Bab V)
Bab V.pdf
Restricted to Registered users only
Download (184kB)
[thumbnail of Daftar Pustaka] Text (Daftar Pustaka)
Daftar Pustaka.pdf
Restricted to Registered users only
Download (122kB)
[thumbnail of Lampiran] Text (Lampiran)
Lampiran.pdf
Restricted to Registered users only
Download (531kB)
[thumbnail of Naskah Publikasi] Text (Naskah Publikasi)
Naskah Publikasi.pdf
Restricted to Registered users only
Download (681kB)
[thumbnail of Full Text] Text (Full Text)
Full Text.pdf
Restricted to Repository staff only
Download (1MB)

Abstract

Hypothermia is defined as a clinical condition when the body temperature is below35°C. Hypothermia usually occurs in patients after surgery. The decrease in body temperature caused by low room temperature during and after surgery is the main factor that causes a sharp drop in the body temperature of hypothermic patients can have a negative impact on the patient. With an incident like this, the author decided to make a tool with the title "Hypothermia Blanket Based on Arduino" to solve problems in hypothermic patients quickly and precisely. The design of this tool uses Arduino uno as a processor and a DS18B20 sensor for temperature readings. Wet heater as a water heater, water pump as a driver of the water cycle from the tool to the blanket and vice versa. The temperature setting and mode will be displayed on the LCD screen. This tool will use 2 modes, namely manual mode, and automatic mode. And for testing the tool will use a digital thermometer to read the temperature. The temperature range used to set the tool is 34°C - 38°C. The highest error percentage value in the automatic mode setting is at a temperature setting of 34°C, 1.38% for tool error and 0.79% for thermometer error. And the highest error percentage value in manual mode setting is at 36°C temperature setting which is 1.33% for tool error and 1.18% for thermometer error. The percentage value of the average error is still within the tolerance value limit, which is ± 5%.

Dosen Pembimbing: MEILIA SAFITRI, S.T., M.ENG. | NIDN0512059001
Item Type: Thesis (S1)
Uncontrolled Keywords: KATA KUNCI: HEATER BASAH, HIPOTERMIA, POMPA AIR, SENSOR SUHU DS18B20
Divisions: Program Vokasi > D3 Teknologi Elektro-medis
Depositing User: M. Erdiansyah
Date Deposited: 18 May 2022 03:13
Last Modified: 18 May 2022 03:13
URI: https://etd.umy.ac.id/id/eprint/29126

Actions (login required)

View Item View Item