OPTIMALISASI DESAIN CETAKAN TUTUP BOTOL 8 CAVITY DENGAN PENDEKATAN SIMULASI & METODE TAGUCHI UNTUK MENCAPAI RUNNER BALANCE & MINIMUM TIME TO FREEZE

Galuh Yudistira (2021) OPTIMALISASI DESAIN CETAKAN TUTUP BOTOL 8 CAVITY DENGAN PENDEKATAN SIMULASI & METODE TAGUCHI UNTUK MENCAPAI RUNNER BALANCE & MINIMUM TIME TO FREEZE. S2 thesis, Universitas Muhammadiyah Yogyakarta.

[thumbnail of Halaman Judul] Text (Halaman Judul)
Halaman Judul.pdf

Download (244kB)
[thumbnail of Lembar Pengesahan] Text (Lembar Pengesahan)
Lembar Pengesahan.pdf
Restricted to Registered users only

Download (286kB)
[thumbnail of Abstrak] Text (Abstrak)
Abstrak.pdf
Restricted to Registered users only

Download (58kB)
[thumbnail of Bab I] Text (Bab I)
Bab I.pdf

Download (93kB)
[thumbnail of Bab II] Text (Bab II)
Bab II.pdf
Restricted to Registered users only

Download (515kB)
[thumbnail of Bab III] Text (Bab III)
Bab III.pdf
Restricted to Registered users only

Download (247kB)
[thumbnail of Bab IV] Text (Bab IV)
Bab IV.pdf
Restricted to Registered users only

Download (682kB)
[thumbnail of Bab V] Text (Bab V)
Bab V.pdf
Restricted to Registered users only

Download (57kB)
[thumbnail of Daftar Pustaka] Text (Daftar Pustaka)
Daftar Pustaka.pdf
Restricted to Registered users only

Download (151kB)
[thumbnail of Lampiran] Text (Lampiran)
Lampiran.pdf
Restricted to Registered users only

Download (141kB)
[thumbnail of Naskah Publikasi] Text (Naskah Publikasi)
Naskah Publikasi.pdf
Restricted to Registered users only

Download (1MB)
[thumbnail of Full Text] Text (Full Text)
Full Text.pdf
Restricted to Repository staff only

Download (1MB)

Abstract

The design in a mold design aims to determine the beginning of the product
before entering the production stage. The 8 cavity bottle cap molded design product is
made usingplastic material High density polyethylene (HDPE)which is hard, strong and
resistant to high temperatures.
The design used aims to measure the process level before entering the
production stage, in this case looking for the bestdesign runner and cooling . Produce
3 types of designs which will be selected the best one. Fordesign cooling using
conformal because it is easier to test using bottle caps. The software used in the design
is Autodesk Inventor 2016 and software simulation Moldflow Insight2015.
From the results of theanalysis moldflow insight, it shows that the results of
each design are that runner 2 and cooling 1 are the best after going through thestages
fill time and time to freeze, part. After knowing the optimal design results, it is
continued by entering indicators in the form ofdiameter runner, melt temperature and
molt temperature obtained from the table in HDPE and study literature. Produce a
design with a diameter of 10 mm melt temperature 180℃ and molt temperature 40℃,
by trying a loweron thesection the temperaturemolt temperature results can remain the
same time to freeze,parts fast trough.

Item Type: Thesis (S2)
Divisions: Fakultas Teknik > Teknik Mesin S1
Depositing User: Unnamed user with email robi@umy.ac.id
Date Deposited: 06 Nov 2021 04:07
Last Modified: 06 Nov 2021 04:07
URI: https://etd.umy.ac.id/id/eprint/6045

Actions (login required)

View Item
View Item